How to recover data from Buffalo Drive Station HD-QS2.0TSU2/R5 NAS

Contents

• Why can’t ordinary software tools restore files from RAID?
• How to take hard disks out of the NAS and connect them to a PC?
  • Restoring data with Hetman RAID Recovery
  • Safe recovery from disk images
  • Where are user’s files stored?
  • Comparison of software for RAID recovery

Why can’t ordinary software tools restore files from RAID?

Conventional hard disks keep user’s data by writing it to their surface in a consecutive way, and this is how an entire file is stored on a single hard disk. However, when data is written to a RAID system, a file is divided into several parts. Then these parts are written consecutively to all hard disks within such array. The size of such parts may range from 2 KB to 2 MB, so each file is stored on several hard disks at the same time.

Such approach helps to speed up read and write operations, and it is evident that saving two parts of a file having the size of 1 GB to two hard disks simultaneously is much faster than saving the same 1 GB of data to one hard disk. However, this peculiarity makes file recovery more complicated.

Various RAID levels store information in different ways. Additionally, manufacturers like Buffalo also introduce some modifications to this process, and that is why data can be written to hard disk in a wide variety of ways.

Are there any specific system logs or event notifications to monitor for early detection of data loss on NAS Buffalo Drive Station HD-QS2.0TSU2/R5 devices?

Yes, there are several system logs and event notifications that you can monitor on NAS Buffalo Drive Station HD-QS2.0TSU2/R5 devices for early detection of data loss. Here are some key logs and notifications to consider:

1. RAID Status Notifications: The NAS device typically provides notifications about the status of the RAID array, such as degraded or failed drives. Monitoring these notifications can help you detect data loss early.
2. SMART (Self-Monitoring, Analysis, and Reporting Technology) Logs: SMART logs provide information about the health and performance of individual hard drives in the NAS device. Monitoring these logs can help you identify potential drive failures or issues that may lead to data loss.
3. System Event Logs: The NAS device maintains system event logs that record various events and errors. Monitoring these logs can help you identify any abnormal behavior or errors that may indicate data loss or other issues.
4. File/Folder Access Logs: Some NAS devices allow you to enable file and folder access logging. Monitoring these logs can help you track file access and detect any unauthorized or suspicious activities that may result in data loss.
5. Email Notifications: Many NAS devices can send email notifications for specific events, such as drive failures, system errors, or abnormal behavior. Setting up email notifications can help you receive immediate alerts and take prompt action to prevent or mitigate data loss.

It's important to consult the user manual or documentation specific to your NAS device model to understand how to enable and monitor these logs and notifications effectively.

How to take hard disks out of the NAS and connect them to a PC?

Although NAS Drive Station HD-QS2.0TSU2/R5 can be accessed over the network, you still need to take the hard disks out of the storage device and connect them to a Windows computer. Only in this case will the software be able to scan them properly. Here is what you should do:

1. Turn off the storage and disconnect it from the power supply.

   WARNING! Before you start taking hard disks out of your NAS device, read the manual carefully. Incorrect actions may damage your network-attached storage and/or the hard disks within the RAID system.

2. Take the hard disks out of the NAS one by one, carefully removing them from their slots. Remember that the disks are extremely vulnerable: hitting or dropping them may result in serious physical damage.

3. Make sure to mark each hard disk in accordance with how they were installed inside the NAS.

4. Remove the hard disks and connect them to the computer. In this video, we have explored what ports are used to connect hard disks, and what to do if there are not enough ports or connectors.

   Go to view

   

   How to Order Remote Data Recovery

Restoring data with Hetman RAID Recovery

This program recovers data from damaged RAID arrays and is fully compatible with Buffalo Drive Station HD-QS2.0TSU2/R5. The hard disks that make up the RAID contain technical information about the algorithm used to save files. When launched, Hetman RAID Recovery reads this information and puts the damaged array together. Then you can open the disk and save your files. Also, you can recover the files accidentally deleted from the network drive.

Go to view

How to recover data from a Buffalo

Drive Station HD-QS2.0TSU2/R5 has 4 HDD slots, and it supports the following array types:

• RAID 0;
• RAID 1;
• RAID 5;
• RAID 6;
• JBOD;

NAS supports:

• exFAT, VFAT, FAT 12 / 16 / 32;
• NTFS / ReFS;
• APFS / HFS+;
• Ext2 / 3 / 4 / ReiserFS / XFS / UFS / ZFS / Btrfs;
• VMFS / HikvisionFS;

Safe recovery from disk images

This utility lets you save an entire copy of the disk to file and then work with this image instead of the actual disk. Such feature helps to protect data on the disk from:

• Overwriting during the recovery process;
• Loss resulting from bad sectors;
• User mistakes.

To create an image, do the following:

1. Make sure that you have enough free space to save the image. The image file size usually equals the disk size.

2. Select the disk in the main window, and choose from the menu Tools – Save Disk. You can select multiple disks to be saved.

3. When the image creation wizard starts, you can choose to save the entire disk or select only a part of it. Specify the parameters and click Next.

   

4. At this stage, you need to choose a directory where to save the image. Choose any disk connected to this PC, or save the image by FTP.

   

Where are user’s files stored?

The Buffalo Drive Station HD-QS2.0TSU2/R5 network-attached storage keeps OS Linux operating system files on a separate RAID 1 (mirrored) array. Usually, all NAS systems create several volumes on every hard disk, and the first of them takes up to 2 Gb of space. This is where operating system files are stored. Other volumes are united into a RAID array where user’s data is written.

Comparison of software for RAID recovery