Essential Tips for RAID Array Recovery in NAS Digiever DBS-16364-RM

Contents

• Why can’t ordinary software tools restore files from RAID?
• How to take hard disks out of the NAS and connect them to a PC?
  • Restoring data with Hetman RAID Recovery
  • Safe recovery from disk images
  • Where are user’s files stored?
  • Comparison of software for RAID recovery

Why can’t ordinary software tools restore files from RAID?

Conventional hard disks keep user’s data by writing it to their surface in a consecutive way, and this is how an entire file is stored on a single hard disk. However, when data is written to a RAID system, a file is divided into several parts. Then these parts are written consecutively to all hard disks within such array. The size of such parts may range from 2 KB to 2 MB, so each file is stored on several hard disks at the same time.

Such approach helps to speed up read and write operations, and it is evident that saving two parts of a file having the size of 1 GB to two hard disks simultaneously is much faster than saving the same 1 GB of data to one hard disk. However, this peculiarity makes file recovery more complicated.

Various RAID levels store information in different ways. Additionally, manufacturers like Digiever also introduce some modifications to this process, and that is why data can be written to hard disk in a wide variety of ways.

How can RAID (Redundant Array of Independent Disks) configurations impact data loss in NAS Digiever DBS-16364-RM devices?

RAID configurations in NAS Digiever DBS-16364-RM devices can have a significant impact on data loss prevention. Here are some ways RAID can affect data loss in these devices:

1. Redundancy: RAID configurations provide redundancy by spreading data across multiple disks. In case of a disk failure, the data can be rebuilt or retrieved from the remaining disks, minimizing the risk of data loss.
2. Fault tolerance: RAID configurations like RAID 1, RAID 5, or RAID 6 offer fault tolerance, allowing the NAS device to continue functioning even if one or more disks fail. This ensures that data remains accessible and reduces the chances of data loss due to hardware failures.
3. Data recovery: In the event of a disk failure, RAID configurations can facilitate data recovery. Depending on the RAID level, the system can rebuild the lost data using parity information or mirror the data from the remaining disks, preventing any permanent data loss.
4. Performance impact: RAID configurations can impact performance, especially in write-intensive scenarios. Higher RAID levels like RAID 5 or RAID 6 require additional computation for parity calculations, which can slightly reduce write speeds. However, this performance impact is often considered worthwhile for the added data protection.
5. RAID expansion and migration: NAS devices like Digiever DBS-16364-RM often support RAID expansion and migration, allowing users to increase storage capacity or switch to a different RAID level without data loss. This flexibility ensures that data remains intact during changes in the RAID configuration.

It's important to note that while RAID configurations can significantly reduce the risk of data loss, they are not a substitute for regular backups. Implementing a comprehensive backup strategy alongside RAID can provide an additional layer of protection against data loss.

How to take hard disks out of the NAS and connect them to a PC?

Although NAS DBS-16364-RM can be accessed over the network, you still need to take the hard disks out of the storage device and connect them to a Windows computer. Only in this case will the software be able to scan them properly. Here is what you should do:

1. Turn off the storage and disconnect it from the power supply.

   WARNING! Before you start taking hard disks out of your NAS device, read the manual carefully. Incorrect actions may damage your network-attached storage and/or the hard disks within the RAID system.

2. Take the hard disks out of the NAS one by one, carefully removing them from their slots. Remember that the disks are extremely vulnerable: hitting or dropping them may result in serious physical damage.

3. Make sure to mark each hard disk in accordance with how they were installed inside the NAS.

4. Remove the hard disks and connect them to the computer. In this video, we have explored what ports are used to connect hard disks, and what to do if there are not enough ports or connectors.

   Go to view

   

   How to Order Remote Data Recovery

Restoring data with Hetman RAID Recovery

This program recovers data from damaged RAID arrays and is fully compatible with Digiever DBS-16364-RM. The hard disks that make up the RAID contain technical information about the algorithm used to save files. When launched, Hetman RAID Recovery reads this information and puts the damaged array together. Then you can open the disk and save your files. Also, you can recover the files accidentally deleted from the network drive.

Go to view

How to recover data from a Digiever

DBS-16364-RM has 16 HDD slots, and it supports the following array types:

• RAID 0;
• RAID 1;
• RAID 5;
• RAID 6;
• RAID 50;
• RAID 60;
• JBOD;

NAS supports:

• exFAT, VFAT, FAT 12 / 16 / 32;
• NTFS / ReFS;
• APFS / HFS+;
• Ext2 / 3 / 4 / ReiserFS / XFS / UFS / ZFS / Btrfs;
• VMFS / HikvisionFS;

Safe recovery from disk images

This utility lets you save an entire copy of the disk to file and then work with this image instead of the actual disk. Such feature helps to protect data on the disk from:

• Overwriting during the recovery process;
• Loss resulting from bad sectors;
• User mistakes.

To create an image, do the following:

1. Make sure that you have enough free space to save the image. The image file size usually equals the disk size.

2. Select the disk in the main window, and choose from the menu Tools – Save Disk. You can select multiple disks to be saved.

3. When the image creation wizard starts, you can choose to save the entire disk or select only a part of it. Specify the parameters and click Next.

   

4. At this stage, you need to choose a directory where to save the image. Choose any disk connected to this PC, or save the image by FTP.

   

Where are user’s files stored?

The Digiever DBS-16364-RM network-attached storage keeps OS Linux operating system files on a separate RAID 1 (mirrored) array. Usually, all NAS systems create several volumes on every hard disk, and the first of them takes up to 2 Gb of space. This is where operating system files are stored. Other volumes are united into a RAID array where user’s data is written.

Comparison of software for RAID recovery