How to Get Data from RAID Disks If NAS Buffalo TeraStation TS5800D1608 Doesn’t Boot

Contents

• Why Regular Data Recovery Tools Can’t Restore Files from RAID
• Key Information About the NAS Buffalo TeraStation TS5800D1608
• How to Remove Hard Disks from Your NAS and Connect Them to a PC
  • Step-by-Step Data Recovery with Hetman RAID Recovery
  • How to Safely Recover Data from Disk Images
  • Where Are the User’s Files Actually Stored?
  • RAID Recovery Software: Detailed Comparison

Why Regular Data Recovery Tools Can’t Restore Files from RAID

Conventional hard drives store user data by writing it sequentially across the disk surface, which means an entire file is typically located on a single drive. In contrast, when data is written to a RAID array, each file is split into multiple fragments. These fragments are then distributed and written in sequence across all the drives in the array. Depending on the configuration, fragment sizes can range from 2 KB to 2 MB, so every file is physically stored across several disks at once.

This approach significantly increases read and write performance — after all, writing two halves of a 1 GB file to two drives simultaneously is much faster than writing the full 1 GB to a single disk. However, this same mechanism makes file recovery far more complex.

Different RAID levels use different methods to distribute and protect data. On top of that, manufacturers like Buffalo often add their own proprietary structures and variations. As a result, data can be written to disks in many different formats, and each requires a specific approach during recovery.

How can quality of service (QoS) settings impact data transfer reliability on NAS Buffalo TeraStation TS5800D1608 devices?

Quality of Service (QoS) settings can have a significant impact on data transfer reliability on NAS Buffalo TeraStation TS5800D1608 devices. Here are a few ways QoS settings can affect data transfer reliability:

1. Bandwidth Allocation: QoS settings allow you to allocate and prioritize bandwidth for specific applications or services. By assigning higher priority to critical data transfers, you ensure that they receive sufficient bandwidth, reducing the chances of packet loss or delay.
2. Traffic Management: QoS settings enable you to manage and control network traffic, preventing congestion and ensuring smooth data transfers. By regulating the flow of data, you can avoid bottlenecks and maintain consistent transfer speeds.
3. Prioritization: QoS settings allow you to prioritize data transfers based on their importance or urgency. By assigning higher priority to certain transfers, you ensure that they are processed and delivered promptly, minimizing the risk of delays or interruptions.
4. Packet Prioritization: QoS settings can prioritize individual packets within a data transfer. This ensures that critical packets are delivered first, reducing the impact of latency or network congestion on overall data transfer reliability.
5. Network Stability: QoS settings can help maintain a stable network environment by controlling and managing network resources. By preventing excessive bandwidth usage by certain applications or users, QoS settings can ensure a consistent and reliable data transfer experience.

Overall, QoS settings on NAS Buffalo TeraStation TS5800D1608 devices can enhance data transfer reliability by optimizing bandwidth allocation, managing network traffic, and prioritizing critical transfers.

How to Remove Hard Disks from Your NAS and Connect Them to a PC

Although the NAS TeraStation TS5800D1608 can be accessed over the network, you still need to remove its hard disks and connect them directly to a Windows PC. Only then can the recovery software properly scan and analyze the drives. Follow these steps:

1. Power off the NAS and disconnect it from the power source.

   WARNING! Before removing any drives, carefully read the device manual. Improper actions may damage both the NAS enclosure and the hard disks in the RAID array.

2. Remove the hard disks one by one, gently sliding each drive out of its slot. Remember that hard disks are highly sensitive: any impact or drop can cause serious physical damage.

3. Label each hard disk according to its position inside the NAS. The order of the drives is crucial for correct RAID reconstruction.

4. Connect the drives to your computer. In this video, we explain which ports you can use to connect hard disks and what to do if your PC does not have enough free connectors.

   Go to view

   

   How to Order Remote Data Recovery

Step-by-Step Data Recovery with Hetman RAID Recovery

This program restores data from damaged RAID arrays and is fully compatible with Buffalo TeraStation TS5800D1608. Each hard disk in the array contains technical metadata describing how files were written. When launched, Hetman RAID Recovery analyzes this metadata, automatically reconstructs the damaged array, and provides access to its contents. After that, you can browse the recovered disk and save your files. The program can also restore files that were accidentally deleted from the network drive.

Go to view

How to recover data from a Buffalo

TeraStation TS5800D1608 has 1 HDD slots, and it supports the following array types:

• RAID 0;
• RAID 1;
• RAID 5;
• RAID 6;
• RAID 50;
• RAID 60;
• JBOD;

NAS supports:

• exFAT, VFAT, FAT 12 / 16 / 32;
• NTFS / ReFS;
• APFS / HFS+;
• Ext2 / 3 / 4 / ReiserFS / XFS / UFS / ZFS / Btrfs;
• VMFS / HikvisionFS;

How to Safely Recover Data from Disk Images

This utility allows you to create a complete copy of a disk and work with the disk image instead of the physical drive. This approach helps protect your data from:

• Overwriting during the recovery process;
• Additional data loss caused by bad sectors;
• User errors.

To create a disk image, follow these steps:

1. Ensure you have enough free space to store the image. Its size will typically match the size of the original disk.

2. In the main window, select the target disk and choose Tools - Save Disk. You can also select multiple disks if needed.

3. When the Image Creation Wizard opens, select whether you want to save the entire disk or only a specific region. Adjust the settings and click Next.

   

4. Choose the directory where the image will be saved. You may select any available disk connected to your PC or upload the image via FTP.

   

Where Are the User’s Files Actually Stored?

The Buffalo TeraStation TS5800D1608 network-attached storage keeps OS Linux operating system files on a separate RAID 1 (mirrored) array. Usually, all NAS systems create several volumes on every hard disk, and the first of them takes up to 2 Gb of space. This is where operating system files are stored. Other volumes are united into a RAID array where user’s data is written.

RAID Recovery Software: Detailed Comparison