How to Access Files on a RAID Disk When NAS Promise Vess 1730s is Offline: Practical Steps

Contents

• Why Regular Data Recovery Tools Can’t Restore Files from RAID
• Key Information About the NAS Promise Vess 1730s
• How to Remove Hard Disks from Your NAS and Connect Them to a PC
  • Step-by-Step Data Recovery with Hetman RAID Recovery
  • How to Safely Recover Data from Disk Images
  • Where Are the User’s Files Actually Stored?
  • RAID Recovery Software: Detailed Comparison

Why Regular Data Recovery Tools Can’t Restore Files from RAID

Conventional hard drives store user data by writing it sequentially across the disk surface, which means an entire file is typically located on a single drive. In contrast, when data is written to a RAID array, each file is split into multiple fragments. These fragments are then distributed and written in sequence across all the drives in the array. Depending on the configuration, fragment sizes can range from 2 KB to 2 MB, so every file is physically stored across several disks at once.

This approach significantly increases read and write performance — after all, writing two halves of a 1 GB file to two drives simultaneously is much faster than writing the full 1 GB to a single disk. However, this same mechanism makes file recovery far more complex.

Different RAID levels use different methods to distribute and protect data. On top of that, manufacturers like Promise often add their own proprietary structures and variations. As a result, data can be written to disks in many different formats, and each requires a specific approach during recovery.

How can the use of specific file-sharing protocols impact data loss risks on NAS Promise Vess 1730s devices?

The use of specific file-sharing protocols can impact data loss risks on NAS Promise Vess 1730s devices in several ways:

1. Security vulnerabilities: Different file-sharing protocols have different levels of security. Some protocols may have known vulnerabilities that can be exploited by attackers to gain unauthorized access to the device or the data stored on it. This can lead to data loss or compromise.
2. Encryption capabilities: Some file-sharing protocols support encryption of data during transmission, while others may not. If sensitive data is being shared over a protocol that does not provide encryption, it increases the risk of data interception and loss.
3. Access control mechanisms: File-sharing protocols may have varying levels of access control mechanisms. If a protocol does not provide granular control over user permissions and access rights, it can increase the risk of unauthorized users gaining access to sensitive data and potentially causing data loss.
4. Compatibility and interoperability: Different file-sharing protocols may have varying levels of compatibility and interoperability with different operating systems and devices. If a protocol is not widely supported or is incompatible with the devices or systems being used, it can lead to data loss or difficulties in accessing and sharing data.
5. Performance and reliability: The choice of file-sharing protocol can also impact the performance and reliability of data transfers. Some protocols may be faster and more reliable than others, reducing the risk of data loss due to transmission errors or interruptions.

To minimize data loss risks, it is important to choose file-sharing protocols that prioritize security, encryption, access control, compatibility, and reliability. Regularly updating the firmware of the NAS device and implementing other security measures like strong passwords and regular backups can also help mitigate the risks.

How to Remove Hard Disks from Your NAS and Connect Them to a PC

Although the NAS Vess 1730s can be accessed over the network, you still need to remove its hard disks and connect them directly to a Windows PC. Only then can the recovery software properly scan and analyze the drives. Follow these steps:

1. Power off the NAS and disconnect it from the power source.

   WARNING! Before removing any drives, carefully read the device manual. Improper actions may damage both the NAS enclosure and the hard disks in the RAID array.

2. Remove the hard disks one by one, gently sliding each drive out of its slot. Remember that hard disks are highly sensitive: any impact or drop can cause serious physical damage.

3. Label each hard disk according to its position inside the NAS. The order of the drives is crucial for correct RAID reconstruction.

4. Connect the drives to your computer. In this video, we explain which ports you can use to connect hard disks and what to do if your PC does not have enough free connectors.

   Go to view

   

   How to Order Remote Data Recovery

Step-by-Step Data Recovery with Hetman RAID Recovery

This program restores data from damaged RAID arrays and is fully compatible with Promise Vess 1730s. Each hard disk in the array contains technical metadata describing how files were written. When launched, Hetman RAID Recovery analyzes this metadata, automatically reconstructs the damaged array, and provides access to its contents. After that, you can browse the recovered disk and save your files. The program can also restore files that were accidentally deleted from the network drive.

Go to view

How to recover data from a Promise

Vess 1730s has 12 HDD slots, and it supports the following array types:

• RAID 0;
• RAID 1;
• RAID 1E;
• RAID 3;
• RAID 5;
• RAID 6;
• RAID 30;
• RAID 50;
• RAID 60;
• JBOD;

NAS supports:

• exFAT, VFAT, FAT 12 / 16 / 32;
• NTFS / ReFS;
• APFS / HFS+;
• Ext2 / 3 / 4 / ReiserFS / XFS / UFS / ZFS / Btrfs;
• VMFS / HikvisionFS;

How to Safely Recover Data from Disk Images

This utility allows you to create a complete copy of a disk and work with the disk image instead of the physical drive. This approach helps protect your data from:

• Overwriting during the recovery process;
• Additional data loss caused by bad sectors;
• User errors.

To create a disk image, follow these steps:

1. Ensure you have enough free space to store the image. Its size will typically match the size of the original disk.

2. In the main window, select the target disk and choose Tools - Save Disk. You can also select multiple disks if needed.

3. When the Image Creation Wizard opens, select whether you want to save the entire disk or only a specific region. Adjust the settings and click Next.

   

4. Choose the directory where the image will be saved. You may select any available disk connected to your PC or upload the image via FTP.

   

Where Are the User’s Files Actually Stored?

The Promise Vess 1730s network-attached storage keeps OS Linux operating system files on a separate RAID 1 (mirrored) array. Usually, all NAS systems create several volumes on every hard disk, and the first of them takes up to 2 Gb of space. This is where operating system files are stored. Other volumes are united into a RAID array where user’s data is written.

RAID Recovery Software: Detailed Comparison