Steps to Recover a Damaged RAID Array on NAS Buffalo Drive Station HD-LX1.0TU3 with Several Disks

Contents

• Why Regular Data Recovery Tools Can’t Restore Files from RAID
• Key Information About the NAS Buffalo Drive Station HD-LX1.0TU3
• How to Remove Hard Disks from Your NAS and Connect Them to a PC
  • Step-by-Step Data Recovery with Hetman RAID Recovery
  • How to Safely Recover Data from Disk Images
  • Where Are the User’s Files Actually Stored?
  • RAID Recovery Software: Detailed Comparison

Why Regular Data Recovery Tools Can’t Restore Files from RAID

Conventional hard drives store user data by writing it sequentially across the disk surface, which means an entire file is typically located on a single drive. In contrast, when data is written to a RAID array, each file is split into multiple fragments. These fragments are then distributed and written in sequence across all the drives in the array. Depending on the configuration, fragment sizes can range from 2 KB to 2 MB, so every file is physically stored across several disks at once.

This approach significantly increases read and write performance — after all, writing two halves of a 1 GB file to two drives simultaneously is much faster than writing the full 1 GB to a single disk. However, this same mechanism makes file recovery far more complex.

Different RAID levels use different methods to distribute and protect data. On top of that, manufacturers like Buffalo often add their own proprietary structures and variations. As a result, data can be written to disks in many different formats, and each requires a specific approach during recovery.

Are there any known limitations or performance bottlenecks that can increase data loss risks for NAS Buffalo Drive Station HD-LX1.0TU3 devices?

While it is difficult to provide a comprehensive list of all known limitations or performance bottlenecks specific to the NAS Buffalo Drive Station HD-LX1.0TU3 devices, there are a few general factors that can potentially increase data loss risks:

1. Hardware Failure: Like any electronic device, the NAS Buffalo Drive Station HD-LX1.0TU3 is susceptible to hardware failures such as hard drive crashes or power supply issues. These failures can lead to data loss if proper backup and redundancy measures are not in place.
2. Lack of Redundancy: If the NAS is not configured with a RAID (Redundant Array of Independent Disks) setup or any other redundancy mechanism, a single drive failure can result in data loss. It is recommended to configure the NAS with a RAID level that suits your needs and provides data redundancy.
3. Insufficient Backup Strategy: Relying solely on the NAS as the primary storage without implementing regular backups to an external device or cloud storage can increase the risk of data loss. Accidental file deletion, malware attacks, or NAS failure could result in permanent data loss without a proper backup strategy.
4. Network Connectivity: The performance and reliability of the NAS can be affected by the network infrastructure it is connected to. Slow network speeds, network congestion, or intermittent connectivity issues can impact data transfer and increase the risk of data loss during file operations.
5. Firmware or Software Bugs: Like any software-based system, NAS devices can have firmware or software bugs that may result in unexpected behavior or data corruption. It is important to keep the firmware up to date and regularly check for any known issues or updates from the manufacturer.

To mitigate these risks, it is recommended to implement a comprehensive backup strategy, regularly update firmware and software, use a reliable network infrastructure, and consider redundancy options such as RAID configurations. Additionally, consulting the product documentation and support resources provided by Buffalo Technology can provide more specific information about any known limitations or performance bottlenecks for the NAS Buffalo Drive Station HD-LX1.0TU3 devices.

How to Remove Hard Disks from Your NAS and Connect Them to a PC

Although the NAS Drive Station HD-LX1.0TU3 can be accessed over the network, you still need to remove its hard disks and connect them directly to a Windows PC. Only then can the recovery software properly scan and analyze the drives. Follow these steps:

1. Power off the NAS and disconnect it from the power source.

   WARNING! Before removing any drives, carefully read the device manual. Improper actions may damage both the NAS enclosure and the hard disks in the RAID array.

2. Remove the hard disks one by one, gently sliding each drive out of its slot. Remember that hard disks are highly sensitive: any impact or drop can cause serious physical damage.

3. Label each hard disk according to its position inside the NAS. The order of the drives is crucial for correct RAID reconstruction.

4. Connect the drives to your computer. In this video, we explain which ports you can use to connect hard disks and what to do if your PC does not have enough free connectors.

   Go to view

   

   How to Order Remote Data Recovery

Step-by-Step Data Recovery with Hetman RAID Recovery

This program restores data from damaged RAID arrays and is fully compatible with Buffalo Drive Station HD-LX1.0TU3. Each hard disk in the array contains technical metadata describing how files were written. When launched, Hetman RAID Recovery analyzes this metadata, automatically reconstructs the damaged array, and provides access to its contents. After that, you can browse the recovered disk and save your files. The program can also restore files that were accidentally deleted from the network drive.

Go to view

How to recover data from a Buffalo

Drive Station HD-LX1.0TU3 has 1 HDD slots, and it supports the following array types:

• RAID 0;
• RAID 1;
• JBOD;

NAS supports:

• exFAT, VFAT, FAT 12 / 16 / 32;
• NTFS / ReFS;
• APFS / HFS+;
• Ext2 / 3 / 4 / ReiserFS / XFS / UFS / ZFS / Btrfs;
• VMFS / HikvisionFS;

How to Safely Recover Data from Disk Images

This utility allows you to create a complete copy of a disk and work with the disk image instead of the physical drive. This approach helps protect your data from:

• Overwriting during the recovery process;
• Additional data loss caused by bad sectors;
• User errors.

To create a disk image, follow these steps:

1. Ensure you have enough free space to store the image. Its size will typically match the size of the original disk.

2. In the main window, select the target disk and choose Tools - Save Disk. You can also select multiple disks if needed.

3. When the Image Creation Wizard opens, select whether you want to save the entire disk or only a specific region. Adjust the settings and click Next.

   

4. Choose the directory where the image will be saved. You may select any available disk connected to your PC or upload the image via FTP.

   

Where Are the User’s Files Actually Stored?

The Buffalo Drive Station HD-LX1.0TU3 network-attached storage keeps OS Linux operating system files on a separate RAID 1 (mirrored) array. Usually, all NAS systems create several volumes on every hard disk, and the first of them takes up to 2 Gb of space. This is where operating system files are stored. Other volumes are united into a RAID array where user’s data is written.

RAID Recovery Software: Detailed Comparison