How to Get Files Off RAID Disks If NAS Buffalo TeraStation TS-8VH24TL/R6 Is Unresponsive

Contents

• Why Regular Data Recovery Tools Can’t Restore Files from RAID
• Key Information About the NAS Buffalo TeraStation TS-8VH24TL/R6
• How to Remove Hard Disks from Your NAS and Connect Them to a PC
  • Step-by-Step Data Recovery with Hetman RAID Recovery
  • How to Safely Recover Data from Disk Images
  • Where Are the User’s Files Actually Stored?
  • RAID Recovery Software: Detailed Comparison

Why Regular Data Recovery Tools Can’t Restore Files from RAID

Conventional hard drives store user data by writing it sequentially across the disk surface, which means an entire file is typically located on a single drive. In contrast, when data is written to a RAID array, each file is split into multiple fragments. These fragments are then distributed and written in sequence across all the drives in the array. Depending on the configuration, fragment sizes can range from 2 KB to 2 MB, so every file is physically stored across several disks at once.

This approach significantly increases read and write performance — after all, writing two halves of a 1 GB file to two drives simultaneously is much faster than writing the full 1 GB to a single disk. However, this same mechanism makes file recovery far more complex.

Different RAID levels use different methods to distribute and protect data. On top of that, manufacturers like Buffalo often add their own proprietary structures and variations. As a result, data can be written to disks in many different formats, and each requires a specific approach during recovery.

How can conducting regular backups on external storage devices mitigate data loss risks for NAS Buffalo TeraStation TS-8VH24TL/R6 devices?

Conducting regular backups on external storage devices can mitigate data loss risks for NAS Buffalo TeraStation TS-8VH24TL/R6 devices by providing an additional layer of protection and redundancy. Here's how it can be done:

1. Choose a reliable external storage device: Select an external storage device that is compatible with the NAS Buffalo TeraStation and has enough capacity to accommodate your backup needs. It can be an external hard drive, USB flash drive, or a network-attached storage (NAS) device.
2. Set up a backup schedule: Establish a regular backup schedule to ensure that your data is consistently backed up. Depending on the frequency of data changes, you can choose daily, weekly, or monthly backups. Automating the backup process can help ensure regularity.
3. Use backup software: Utilize backup software that is compatible with both the NAS Buffalo TeraStation and the external storage device. This software can help streamline the backup process, provide additional features like encryption or compression, and enable easy restoration when needed.
4. Select appropriate backup method: Decide on the backup method that suits your requirements. It can be a full backup, where all data is copied to the external storage device, or an incremental backup, where only the changes made since the last backup are stored. Incremental backups are generally faster and save storage space.
5. Store backups offsite: To mitigate risks like theft, fire, or natural disasters, store your external storage device containing backups in a secure offsite location. This ensures that even if the NAS Buffalo TeraStation is damaged or inaccessible, your data remains safe.
6. Test and verify backups: Periodically test and verify the integrity of your backups. This involves restoring a subset of data from the external storage device to ensure that the backup process is working correctly and the data can be successfully recovered if needed.
7. Maintain multiple backups: Consider maintaining multiple backups on different external storage devices or locations for added redundancy. This further reduces the risk of data loss in case of hardware failures or other unforeseen events.

By following these steps, regularly backing up your NAS Buffalo TeraStation to external storage devices can significantly mitigate the risks of data loss and provide peace of mind.

How to Remove Hard Disks from Your NAS and Connect Them to a PC

Although the NAS TeraStation TS-8VH24TL/R6 can be accessed over the network, you still need to remove its hard disks and connect them directly to a Windows PC. Only then can the recovery software properly scan and analyze the drives. Follow these steps:

1. Power off the NAS and disconnect it from the power source.

   WARNING! Before removing any drives, carefully read the device manual. Improper actions may damage both the NAS enclosure and the hard disks in the RAID array.

2. Remove the hard disks one by one, gently sliding each drive out of its slot. Remember that hard disks are highly sensitive: any impact or drop can cause serious physical damage.

3. Label each hard disk according to its position inside the NAS. The order of the drives is crucial for correct RAID reconstruction.

4. Connect the drives to your computer. In this video, we explain which ports you can use to connect hard disks and what to do if your PC does not have enough free connectors.

   Go to view

   

   How to Order Remote Data Recovery

Step-by-Step Data Recovery with Hetman RAID Recovery

This program restores data from damaged RAID arrays and is fully compatible with Buffalo TeraStation TS-8VH24TL/R6. Each hard disk in the array contains technical metadata describing how files were written. When launched, Hetman RAID Recovery analyzes this metadata, automatically reconstructs the damaged array, and provides access to its contents. After that, you can browse the recovered disk and save your files. The program can also restore files that were accidentally deleted from the network drive.

Go to view

How to recover data from a Buffalo

TeraStation TS-8VH24TL/R6 has 1 HDD slots, and it supports the following array types:

• RAID 0;
• RAID 1;
• RAID 5;
• RAID 6;
• RAID 50;
• RAID 60;
• JBOD;

NAS supports:

• exFAT, VFAT, FAT 12 / 16 / 32;
• NTFS / ReFS;
• APFS / HFS+;
• Ext2 / 3 / 4 / ReiserFS / XFS / UFS / ZFS / Btrfs;
• VMFS / HikvisionFS;

How to Safely Recover Data from Disk Images

This utility allows you to create a complete copy of a disk and work with the disk image instead of the physical drive. This approach helps protect your data from:

• Overwriting during the recovery process;
• Additional data loss caused by bad sectors;
• User errors.

To create a disk image, follow these steps:

1. Ensure you have enough free space to store the image. Its size will typically match the size of the original disk.

2. In the main window, select the target disk and choose Tools - Save Disk. You can also select multiple disks if needed.

3. When the Image Creation Wizard opens, select whether you want to save the entire disk or only a specific region. Adjust the settings and click Next.

   

4. Choose the directory where the image will be saved. You may select any available disk connected to your PC or upload the image via FTP.

   

Where Are the User’s Files Actually Stored?

The Buffalo TeraStation TS-8VH24TL/R6 network-attached storage keeps OS Linux operating system files on a separate RAID 1 (mirrored) array. Usually, all NAS systems create several volumes on every hard disk, and the first of them takes up to 2 Gb of space. This is where operating system files are stored. Other volumes are united into a RAID array where user’s data is written.

RAID Recovery Software: Detailed Comparison