Accessing RAID Array Data When NAS Buffalo TeraStation TS3400D0804 Fails to Start

Contents

• Why Regular Data Recovery Tools Can’t Restore Files from RAID
• Key Information About the NAS Buffalo TeraStation TS3400D0804
• How to Remove Hard Disks from Your NAS and Connect Them to a PC
  • Step-by-Step Data Recovery with Hetman RAID Recovery
  • How to Safely Recover Data from Disk Images
  • Where Are the User’s Files Actually Stored?
  • RAID Recovery Software: Detailed Comparison

Why Regular Data Recovery Tools Can’t Restore Files from RAID

Conventional hard drives store user data by writing it sequentially across the disk surface, which means an entire file is typically located on a single drive. In contrast, when data is written to a RAID array, each file is split into multiple fragments. These fragments are then distributed and written in sequence across all the drives in the array. Depending on the configuration, fragment sizes can range from 2 KB to 2 MB, so every file is physically stored across several disks at once.

This approach significantly increases read and write performance — after all, writing two halves of a 1 GB file to two drives simultaneously is much faster than writing the full 1 GB to a single disk. However, this same mechanism makes file recovery far more complex.

Different RAID levels use different methods to distribute and protect data. On top of that, manufacturers like Buffalo often add their own proprietary structures and variations. As a result, data can be written to disks in many different formats, and each requires a specific approach during recovery.

How can data fragmentation impact data availability and potential loss on NAS Buffalo TeraStation TS3400D0804 devices?

Data fragmentation can impact data availability and potential loss on NAS Buffalo TeraStation TS3400D0804 devices in the following ways:

1. Reduced Performance: Data fragmentation can lead to slower read and write speeds on the NAS device. When files are fragmented, the NAS has to access multiple locations on the hard drive to retrieve the complete file, resulting in increased seek times and decreased performance.
2. Increased Risk of Data Loss: Fragmented data is more susceptible to data loss. If a single fragment of a file becomes corrupted or lost, the entire file may become inaccessible. This can lead to data loss if backups are not regularly performed.
3. Difficulty in Data Recovery: In the event of a hardware failure or accidental deletion, fragmented data can be more challenging to recover. If the file system metadata is fragmented, it becomes harder for data recovery tools to locate and reconstruct the files.
4. Decreased Storage Efficiency: Fragmentation can also impact storage efficiency on the NAS device. Fragmented files take up more space on the hard drive as the free space becomes scattered across different areas. This reduces the overall usable storage capacity and requires more frequent disk defragmentation or file system optimization.
5. Increased Wear and Tear on Hard Drives: Fragmentation increases the number of disk operations required to read or write files, which can lead to increased wear and tear on the hard drives. This may result in a higher likelihood of hard drive failures and data loss.

To mitigate the impact of data fragmentation on a NAS Buffalo TeraStation TS3400D0804, regular disk defragmentation or file system optimization should be performed. This process rearranges the fragmented data on the hard drives, improving performance, reducing the risk of data loss, and increasing storage efficiency. Additionally, implementing a backup strategy that includes regular backups of critical data can help protect against potential data loss.

How to Remove Hard Disks from Your NAS and Connect Them to a PC

Although the NAS TeraStation TS3400D0804 can be accessed over the network, you still need to remove its hard disks and connect them directly to a Windows PC. Only then can the recovery software properly scan and analyze the drives. Follow these steps:

1. Power off the NAS and disconnect it from the power source.

   WARNING! Before removing any drives, carefully read the device manual. Improper actions may damage both the NAS enclosure and the hard disks in the RAID array.

2. Remove the hard disks one by one, gently sliding each drive out of its slot. Remember that hard disks are highly sensitive: any impact or drop can cause serious physical damage.

3. Label each hard disk according to its position inside the NAS. The order of the drives is crucial for correct RAID reconstruction.

4. Connect the drives to your computer. In this video, we explain which ports you can use to connect hard disks and what to do if your PC does not have enough free connectors.

   Go to view

   

   How to Order Remote Data Recovery

Step-by-Step Data Recovery with Hetman RAID Recovery

This program restores data from damaged RAID arrays and is fully compatible with Buffalo TeraStation TS3400D0804. Each hard disk in the array contains technical metadata describing how files were written. When launched, Hetman RAID Recovery analyzes this metadata, automatically reconstructs the damaged array, and provides access to its contents. After that, you can browse the recovered disk and save your files. The program can also restore files that were accidentally deleted from the network drive.

Go to view

How to recover data from a Buffalo

TeraStation TS3400D0804 has 4 HDD slots, and it supports the following array types:

• RAID 0;
• RAID 1;
• RAID 5;
• RAID 6;
• JBOD;

NAS supports:

• exFAT, VFAT, FAT 12 / 16 / 32;
• NTFS / ReFS;
• APFS / HFS+;
• Ext2 / 3 / 4 / ReiserFS / XFS / UFS / ZFS / Btrfs;
• VMFS / HikvisionFS;

How to Safely Recover Data from Disk Images

This utility allows you to create a complete copy of a disk and work with the disk image instead of the physical drive. This approach helps protect your data from:

• Overwriting during the recovery process;
• Additional data loss caused by bad sectors;
• User errors.

To create a disk image, follow these steps:

1. Ensure you have enough free space to store the image. Its size will typically match the size of the original disk.

2. In the main window, select the target disk and choose Tools - Save Disk. You can also select multiple disks if needed.

3. When the Image Creation Wizard opens, select whether you want to save the entire disk or only a specific region. Adjust the settings and click Next.

   

4. Choose the directory where the image will be saved. You may select any available disk connected to your PC or upload the image via FTP.

   

Where Are the User’s Files Actually Stored?

The Buffalo TeraStation TS3400D0804 network-attached storage keeps OS Linux operating system files on a separate RAID 1 (mirrored) array. Usually, all NAS systems create several volumes on every hard disk, and the first of them takes up to 2 Gb of space. This is where operating system files are stored. Other volumes are united into a RAID array where user’s data is written.

RAID Recovery Software: Detailed Comparison