Choosing Data Recovery Software for NAS Buffalo TeraStation TS51210RH12012: Complete Guide

Contents

• Why Regular Data Recovery Tools Can’t Restore Files from RAID
• Key Information About the NAS Buffalo TeraStation TS51210RH12012
• How to Remove Hard Disks from Your NAS and Connect Them to a PC
  • Step-by-Step Data Recovery with Hetman RAID Recovery
  • How to Safely Recover Data from Disk Images
  • Where Are the User’s Files Actually Stored?
  • RAID Recovery Software: Detailed Comparison

Why Regular Data Recovery Tools Can’t Restore Files from RAID

Conventional hard drives store user data by writing it sequentially across the disk surface, which means an entire file is typically located on a single drive. In contrast, when data is written to a RAID array, each file is split into multiple fragments. These fragments are then distributed and written in sequence across all the drives in the array. Depending on the configuration, fragment sizes can range from 2 KB to 2 MB, so every file is physically stored across several disks at once.

This approach significantly increases read and write performance — after all, writing two halves of a 1 GB file to two drives simultaneously is much faster than writing the full 1 GB to a single disk. However, this same mechanism makes file recovery far more complex.

Different RAID levels use different methods to distribute and protect data. On top of that, manufacturers like Buffalo often add their own proprietary structures and variations. As a result, data can be written to disks in many different formats, and each requires a specific approach during recovery.

Are there any specific system logs or event notifications to monitor for early detection of data loss on NAS Buffalo TeraStation TS51210RH12012 devices?

Yes, there are specific system logs and event notifications that can be monitored for early detection of data loss on NAS Buffalo TeraStation TS51210RH12012 devices. Some important logs and notifications to monitor include:

1. System Logs: The system logs on the TeraStation device can provide valuable information about any errors or issues that may be occurring. These logs can be accessed through the device's web interface or via SSH. Look for any error messages related to disk failures, file system corruption, or other issues that may lead to data loss.
2. SMART Monitoring: TeraStation devices support SMART (Self-Monitoring, Analysis, and Reporting Technology) monitoring for hard drives. SMART data provides information about the health and status of the drives, including any potential failures or errors. Monitoring SMART attributes can help detect early signs of drive failure, allowing you to take preventive action before data loss occurs.
3. Email Notifications: TeraStation devices can be configured to send email notifications for various events, including disk errors, RAID failures, and system warnings. Ensure that email notifications are properly set up and regularly check the inbox for any alerts related to potential data loss.
4. RAID Status Monitoring: TeraStation devices typically use RAID (Redundant Array of Independent Disks) configurations for data redundancy and protection. Monitor the RAID status regularly to ensure that all drives are functioning correctly and that the array is in a healthy state. Any degradation or failure in the RAID array can lead to data loss.
5. File System Check Results: The TeraStation device periodically performs file system checks to detect and repair any inconsistencies or errors. Monitor the results of these checks to identify any file system issues that may indicate potential data loss or corruption.

It is important to regularly review and monitor these logs and notifications to detect any early signs of data loss and take appropriate action to prevent further damage or loss of data.

How to Remove Hard Disks from Your NAS and Connect Them to a PC

Although the NAS TeraStation TS51210RH12012 can be accessed over the network, you still need to remove its hard disks and connect them directly to a Windows PC. Only then can the recovery software properly scan and analyze the drives. Follow these steps:

1. Power off the NAS and disconnect it from the power source.

   WARNING! Before removing any drives, carefully read the device manual. Improper actions may damage both the NAS enclosure and the hard disks in the RAID array.

2. Remove the hard disks one by one, gently sliding each drive out of its slot. Remember that hard disks are highly sensitive: any impact or drop can cause serious physical damage.

3. Label each hard disk according to its position inside the NAS. The order of the drives is crucial for correct RAID reconstruction.

4. Connect the drives to your computer. In this video, we explain which ports you can use to connect hard disks and what to do if your PC does not have enough free connectors.

   Go to view

   

   How to Order Remote Data Recovery

Step-by-Step Data Recovery with Hetman RAID Recovery

This program restores data from damaged RAID arrays and is fully compatible with Buffalo TeraStation TS51210RH12012. Each hard disk in the array contains technical metadata describing how files were written. When launched, Hetman RAID Recovery analyzes this metadata, automatically reconstructs the damaged array, and provides access to its contents. After that, you can browse the recovered disk and save your files. The program can also restore files that were accidentally deleted from the network drive.

Go to view

How to recover data from a Buffalo

TeraStation TS51210RH12012 has 12 HDD slots, and it supports the following array types:

• RAID 0;
• RAID 1;
• RAID 5;
• RAID 6;
• RAID 50;
• RAID 60;
• JBOD;

NAS supports:

• exFAT, VFAT, FAT 12 / 16 / 32;
• NTFS / ReFS;
• APFS / HFS+;
• Ext2 / 3 / 4 / ReiserFS / XFS / UFS / ZFS / Btrfs;
• VMFS / HikvisionFS;

How to Safely Recover Data from Disk Images

This utility allows you to create a complete copy of a disk and work with the disk image instead of the physical drive. This approach helps protect your data from:

• Overwriting during the recovery process;
• Additional data loss caused by bad sectors;
• User errors.

To create a disk image, follow these steps:

1. Ensure you have enough free space to store the image. Its size will typically match the size of the original disk.

2. In the main window, select the target disk and choose Tools - Save Disk. You can also select multiple disks if needed.

3. When the Image Creation Wizard opens, select whether you want to save the entire disk or only a specific region. Adjust the settings and click Next.

   

4. Choose the directory where the image will be saved. You may select any available disk connected to your PC or upload the image via FTP.

   

Where Are the User’s Files Actually Stored?

The Buffalo TeraStation TS51210RH12012 network-attached storage keeps OS Linux operating system files on a separate RAID 1 (mirrored) array. Usually, all NAS systems create several volumes on every hard disk, and the first of them takes up to 2 Gb of space. This is where operating system files are stored. Other volumes are united into a RAID array where user’s data is written.

RAID Recovery Software: Detailed Comparison