RAID Array Strategies for Successful NAS Digiever DS-8232-SRM Pro+ Recovery

Contents

• Why Regular Data Recovery Tools Can’t Restore Files from RAID
• Key Information About the NAS Digiever DS-8232-SRM Pro+
• How to Remove Hard Disks from Your NAS and Connect Them to a PC
  • Step-by-Step Data Recovery with Hetman RAID Recovery
  • How to Safely Recover Data from Disk Images
  • Where Are the User’s Files Actually Stored?
  • RAID Recovery Software: Detailed Comparison

Why Regular Data Recovery Tools Can’t Restore Files from RAID

Conventional hard drives store user data by writing it sequentially across the disk surface, which means an entire file is typically located on a single drive. In contrast, when data is written to a RAID array, each file is split into multiple fragments. These fragments are then distributed and written in sequence across all the drives in the array. Depending on the configuration, fragment sizes can range from 2 KB to 2 MB, so every file is physically stored across several disks at once.

This approach significantly increases read and write performance — after all, writing two halves of a 1 GB file to two drives simultaneously is much faster than writing the full 1 GB to a single disk. However, this same mechanism makes file recovery far more complex.

Different RAID levels use different methods to distribute and protect data. On top of that, manufacturers like Digiever often add their own proprietary structures and variations. As a result, data can be written to disks in many different formats, and each requires a specific approach during recovery.

Are there any specific system logs or event notifications to monitor for early detection of data loss on NAS Digiever DS-8232-SRM Pro+ devices?

Yes, there are specific system logs and event notifications that you can monitor for early detection of data loss on Digiever DS-8232-SRM Pro+ NAS devices. Here are a few key logs and notifications to monitor:

1. System Logs: You can monitor the system logs on the NAS device to check for any error messages, warnings, or critical events related to storage or data loss. These logs can provide insights into any potential issues that may lead to data loss.
2. SMART Status: The NAS device usually supports SMART (Self-Monitoring, Analysis, and Reporting Technology) for monitoring the health of hard drives. By monitoring SMART status, you can detect any signs of impending drive failure or errors that may result in data loss.
3. RAID Health and Rebuild Status: If you have configured RAID on your NAS device, it is essential to monitor the RAID health and rebuild status. Any degraded or failed RAID arrays can lead to data loss, so keeping an eye on these notifications is crucial.
4. Disk I/O Errors: Monitoring disk I/O errors can help identify any issues with read or write operations on the NAS device. Frequent or increasing disk I/O errors may indicate potential data loss risks.
5. Backup Job Notifications: If you have configured regular backups on the NAS device, monitoring backup job notifications can help ensure that backups are running successfully. Any backup failures or errors could indicate data loss risks.
6. Network Connectivity Alerts: Monitoring network connectivity alerts can help detect any issues with the NAS device's network connection. Loss of connectivity may impact data access and increase the risk of data loss.

It is recommended to consult the documentation or user manual of your specific NAS model for detailed instructions on monitoring these logs and notifications. Additionally, you can consider setting up email or SMS alerts for critical events to ensure timely detection of data loss risks.

How to Remove Hard Disks from Your NAS and Connect Them to a PC

Although the NAS DS-8232-SRM Pro+ can be accessed over the network, you still need to remove its hard disks and connect them directly to a Windows PC. Only then can the recovery software properly scan and analyze the drives. Follow these steps:

1. Power off the NAS and disconnect it from the power source.

   WARNING! Before removing any drives, carefully read the device manual. Improper actions may damage both the NAS enclosure and the hard disks in the RAID array.

2. Remove the hard disks one by one, gently sliding each drive out of its slot. Remember that hard disks are highly sensitive: any impact or drop can cause serious physical damage.

3. Label each hard disk according to its position inside the NAS. The order of the drives is crucial for correct RAID reconstruction.

4. Connect the drives to your computer. In this video, we explain which ports you can use to connect hard disks and what to do if your PC does not have enough free connectors.

   Go to view

   

   How to Order Remote Data Recovery

Step-by-Step Data Recovery with Hetman RAID Recovery

This program restores data from damaged RAID arrays and is fully compatible with Digiever DS-8232-SRM Pro+. Each hard disk in the array contains technical metadata describing how files were written. When launched, Hetman RAID Recovery analyzes this metadata, automatically reconstructs the damaged array, and provides access to its contents. After that, you can browse the recovered disk and save your files. The program can also restore files that were accidentally deleted from the network drive.

Go to view

How to recover data from a Digiever

DS-8232-SRM Pro+ has 8 HDD slots, and it supports the following array types:

• RAID 0;
• RAID 1;
• RAID 5;
• RAID 6;
• RAID 50;
• RAID 60;
• JBOD;

NAS supports:

• exFAT, VFAT, FAT 12 / 16 / 32;
• NTFS / ReFS;
• APFS / HFS+;
• Ext2 / 3 / 4 / ReiserFS / XFS / UFS / ZFS / Btrfs;
• VMFS / HikvisionFS;

How to Safely Recover Data from Disk Images

This utility allows you to create a complete copy of a disk and work with the disk image instead of the physical drive. This approach helps protect your data from:

• Overwriting during the recovery process;
• Additional data loss caused by bad sectors;
• User errors.

To create a disk image, follow these steps:

1. Ensure you have enough free space to store the image. Its size will typically match the size of the original disk.

2. In the main window, select the target disk and choose Tools - Save Disk. You can also select multiple disks if needed.

3. When the Image Creation Wizard opens, select whether you want to save the entire disk or only a specific region. Adjust the settings and click Next.

   

4. Choose the directory where the image will be saved. You may select any available disk connected to your PC or upload the image via FTP.

   

Where Are the User’s Files Actually Stored?

The Digiever DS-8232-SRM Pro+ network-attached storage keeps OS Linux operating system files on a separate RAID 1 (mirrored) array. Usually, all NAS systems create several volumes on every hard disk, and the first of them takes up to 2 Gb of space. This is where operating system files are stored. Other volumes are united into a RAID array where user’s data is written.

RAID Recovery Software: Detailed Comparison