RAID Disk Access When NAS Promise Vess 1830s is Down: Practical Steps

Contents

• Why Regular Data Recovery Tools Can’t Restore Files from RAID
• Key Information About the NAS Promise Vess 1830s
• How to Remove Hard Disks from Your NAS and Connect Them to a PC
  • Step-by-Step Data Recovery with Hetman RAID Recovery
  • How to Safely Recover Data from Disk Images
  • Where Are the User’s Files Actually Stored?
  • RAID Recovery Software: Detailed Comparison

Why Regular Data Recovery Tools Can’t Restore Files from RAID

Conventional hard drives store user data by writing it sequentially across the disk surface, which means an entire file is typically located on a single drive. In contrast, when data is written to a RAID array, each file is split into multiple fragments. These fragments are then distributed and written in sequence across all the drives in the array. Depending on the configuration, fragment sizes can range from 2 KB to 2 MB, so every file is physically stored across several disks at once.

This approach significantly increases read and write performance — after all, writing two halves of a 1 GB file to two drives simultaneously is much faster than writing the full 1 GB to a single disk. However, this same mechanism makes file recovery far more complex.

Different RAID levels use different methods to distribute and protect data. On top of that, manufacturers like Promise often add their own proprietary structures and variations. As a result, data can be written to disks in many different formats, and each requires a specific approach during recovery.

Can data be lost during the process of upgrading or updating the NAS Promise Vess 1830s device's firmware?

Yes, data can potentially be lost during the process of upgrading or updating the firmware of a NAS (Network Attached Storage) device like the Promise Vess 1830s. While firmware updates are generally designed to be non-destructive and preserve data, there is always a small risk of data loss due to unforeseen issues or errors during the update process.

To minimize the risk of data loss, it is recommended to take certain precautions before performing a firmware update:

1. Backup your data: Make sure to have a complete backup of all your important data stored on the NAS device. This ensures that even if something goes wrong during the firmware update, you can restore your data from the backup.
2. Verify the update process: Before initiating the firmware update, carefully read the update instructions provided by the manufacturer. Ensure that you understand the process and any specific requirements or precautions mentioned.
3. Stable power supply: Ensure that the NAS device has a stable power supply during the firmware update. Power interruptions or fluctuations can cause issues during the update process, potentially leading to data loss.
4. Use official firmware: Only use official firmware updates provided by the manufacturer. Using unofficial or unauthorized firmware can increase the risk of data loss and other issues.
5. Contact manufacturer support: If you have any doubts or concerns about the firmware update process, it is advisable to contact the manufacturer's support team for guidance. They can provide specific instructions and assistance to help minimize the risk of data loss.

By following these precautions and taking necessary backup measures, the risk of data loss during a firmware update can be significantly reduced. However, it is important to understand that there is always a small inherent risk involved in any firmware update process.

How to Remove Hard Disks from Your NAS and Connect Them to a PC

Although the NAS Vess 1830s can be accessed over the network, you still need to remove its hard disks and connect them directly to a Windows PC. Only then can the recovery software properly scan and analyze the drives. Follow these steps:

1. Power off the NAS and disconnect it from the power source.

   WARNING! Before removing any drives, carefully read the device manual. Improper actions may damage both the NAS enclosure and the hard disks in the RAID array.

2. Remove the hard disks one by one, gently sliding each drive out of its slot. Remember that hard disks are highly sensitive: any impact or drop can cause serious physical damage.

3. Label each hard disk according to its position inside the NAS. The order of the drives is crucial for correct RAID reconstruction.

4. Connect the drives to your computer. In this video, we explain which ports you can use to connect hard disks and what to do if your PC does not have enough free connectors.

   Go to view

   

   How to Order Remote Data Recovery

Step-by-Step Data Recovery with Hetman RAID Recovery

This program restores data from damaged RAID arrays and is fully compatible with Promise Vess 1830s. Each hard disk in the array contains technical metadata describing how files were written. When launched, Hetman RAID Recovery analyzes this metadata, automatically reconstructs the damaged array, and provides access to its contents. After that, you can browse the recovered disk and save your files. The program can also restore files that were accidentally deleted from the network drive.

Go to view

How to recover data from a Promise

Vess 1830s has 12 HDD slots, and it supports the following array types:

• RAID 0;
• RAID 1;
• RAID 1E;
• RAID 3;
• RAID 5;
• RAID 6;
• RAID 30;
• RAID 50;
• RAID 60;
• JBOD;

NAS supports:

• exFAT, VFAT, FAT 12 / 16 / 32;
• NTFS / ReFS;
• APFS / HFS+;
• Ext2 / 3 / 4 / ReiserFS / XFS / UFS / ZFS / Btrfs;
• VMFS / HikvisionFS;

How to Safely Recover Data from Disk Images

This utility allows you to create a complete copy of a disk and work with the disk image instead of the physical drive. This approach helps protect your data from:

• Overwriting during the recovery process;
• Additional data loss caused by bad sectors;
• User errors.

To create a disk image, follow these steps:

1. Ensure you have enough free space to store the image. Its size will typically match the size of the original disk.

2. In the main window, select the target disk and choose Tools - Save Disk. You can also select multiple disks if needed.

3. When the Image Creation Wizard opens, select whether you want to save the entire disk or only a specific region. Adjust the settings and click Next.

   

4. Choose the directory where the image will be saved. You may select any available disk connected to your PC or upload the image via FTP.

   

Where Are the User’s Files Actually Stored?

The Promise Vess 1830s network-attached storage keeps OS Linux operating system files on a separate RAID 1 (mirrored) array. Usually, all NAS systems create several volumes on every hard disk, and the first of them takes up to 2 Gb of space. This is where operating system files are stored. Other volumes are united into a RAID array where user’s data is written.

RAID Recovery Software: Detailed Comparison